3D Printing Stack Exchange
3D Printing Stack Exchange

Questions tagged [klipper]

For questions about Klipper Firmware

39 questions
7
votes
1 answer

What is the difference between Linear Advance and Pressure Advance?

I've been trying to do some research on Linear Advance (LA) on Marlin and Pressure Advance (PA) on Klipper, and from my understanding the technology behind each is different, although also similar. If I understand what I have read correctly,…
user995551
  • 238
  • 1
  • 3
  • 7
4
votes
1 answer

Creality Sprite Pro Immediately starts heating hotend on startup

My Setup Ender 3 Pro Creality Board v4.2.7 Klipper Firmware (worked great with the stock Creality Bowden hotend and Creality Direct Drive Extruder) Brand new Creality Sprite Pro hotend. Wiring I have verified that the hotend heater cartridge is…
RQDQ
  • 171
  • 6
4
votes
2 answers

What is recovery velocity in klipper firmware?

I am currently writing a printer.cfg Klipper file for my Tronxy VEHO-600. It is quite a challenge as there is not much info regarding this printer online. Is recovery velocity something that I have to tune while the printer is operational, or can I…
General raid
  • 139
  • 1
  • 6
4
votes
1 answer

Klipper doesn't seem to adjust Z after BED_MESH_CALIBRATE

My rig: Ender 3 BLTouch Octopi Klipper Solid bed mounts I've updated my start G-code from Cura to include a G29 right after G28 and my Klipper config has the following override for G29: [gcode_macro G29] gcode: BED_MESH_CLEAR …
ubiquibacon
  • 161
  • 1
  • 1
  • 6
3
votes
0 answers

Creality K1C printing holes as ovals not circles

I've had five Creality K1C CoreXY 3D printers for about four months. Recently, one of them started having issues where the printed holes aren't coming out as circles and the parts aren't accurate. I'm using the same G-code that works perfectly on my…
cadz
  • 31
  • 3
3
votes
1 answer

What is the difference between position_min and position_endstop parameters in Klipper config file?

I have a Tronxy VEHO-600 and I have a config file, which I got from a friend. My question is regarding the following code block: [stepper_x] step_pin: PE5 dir_pin: !PF1 enable_pin: !PF0 microsteps: 16 rotation_distance: 60 endstop_pin:…
General raid
  • 139
  • 1
  • 6
3
votes
2 answers

Why are the options for PID control commented out in Klipper config file?

I have a Tronxy VEHO-600 I'm currently vamping up with Klipper. I have a config file I got from a friend for a modified VEHO-600. My question is regarding the heater bed code block seen below: [heater_bed] heater_pin: PE2 sensor_type: EPCOS 100K…
General raid
  • 139
  • 1
  • 6
3
votes
2 answers

Klipper: power on before homing

I'd like to force Klipper to perform power on (using M80) before homing. For this purpose I'm trying to override G28: [gcode_macro G28] rename_existing: G28_BASE gcode: M80 G28_BASE { rawparams } But for some reason this does not work, I'm…
Denis Itskovich
  • 133
  • 4
3
votes
1 answer

Steppers stuck with Klipper but work with Marlin

I replaced the fans of my ender 3v2 with Noctuas & Buck converters. During the replacement, I made a mistake and burnt the motherboard (shorted one of the fans). I replaced the motherboard, finished the wiring. The new motherboard is the Creality…
Mathieu VIALES
  • 313
  • 5
  • 13
2
votes
0 answers

Getting "heater bed not heating at expected rate" error when trying to print PETG on a glass bed

I have an Ender 3 Pro with the BigTreeTech SKR mini E3 motherboard and a glass bed, and I use Klipper running on a Pi. About a month ago it started giving me the "heater bed not heating at expected rate" error and stopping during warmup. I was…
Mike
  • 21
  • 1
2
votes
3 answers

Help troubleshooting clogging issue

I have a Neptune 3 Pro with Klipper/MainSail. Direct drive extruder. Recently went to an all metal hotend. I replaced the heatbreak (I am using a 1.75 mm POLISI3D Improved Nano Coated Bimetallic heatbreak) as well as the block (block is all copper…
Snyperx
  • 49
  • 4
2
votes
4 answers

Is there a way to get a "vase mode" for multiple wall prints if you just change the order the walls are printed on each layer?

I was pretty fascinated with vase mode print results thinking it would be awesome if this could be done with at least 2 (or more) walls. Initially I was told that its not possible because the printer would start on the outer wall (or inner), then…
J H
  • 77
  • 5
2
votes
1 answer

How can I get Cura's slicer settings to save into the G-code in a way that Moonraker/Klipper can read them?

I've been using Klipper and Cura for a while now (somewhat new to 3D printing), and I notice whenever I import a new G-code file to Klipper, none of the Slicer settings from Cura display in the G-code files in Klipper. However, when I imported a…
J H
  • 77
  • 5
2
votes
2 answers

How do I move the head?

I have an Elegoo Neptune 4 Pro (love it), and I'm trying to set up a Raspberry Pi with a camera to take a photo every time a layer is complete (to build a time-lapse). This means I'll have to edit the G-code to move the print head to the X-axis…
Jim
  • 183
  • 5
2
votes
0 answers

Configure MKS Robin WiFi Module on FLSUN Super Racer without Klipper

I recently purchased an MKS Robin wifi module for my spouse's FLSUN Super Racer after noticing that the printer runs on an MKS Robin Nano V3.1 board. Immediately after installing the chip, I saw it broadcasting a network, so I connected to it and…
Joshua Dannemann
  • 103
  • 8
1
2 3